← All courses KANSAS STATE UNIVERSITY / ECE 685

L24 / Transmission-line parameters

Transmission-Line Parameters III

Use physical radius to find capacitance, split a nominal π shunt and check phase current against three-phase reactive supply.

Available32 slides
Capacitance and charging power

01 / UNDERSTAND & PREDICT

Understand the model, then predict the result

Finalized lecture slides

Open / download original PDF ↗

Follow the original explanations, diagrams, derivations, and examples in slide order, then use the companion experiment below.

L24 original slide 1 of 32
L24 · 1 / 32
Slide text
Loading slide text.

Figures and page order follow the student PDF for this lecture.

A 138 kV line can draw current even with no receiving-end load. How does conductor geometry create this charging current, and where does it appear in a π circuit?
  • Use physical radius rather than magnetic GMR in electrostatic calculations.
  • Relate C, B, phase current and total three-phase reactive power.
  • Interpret the two shunt branches and reactive power sign.
Capacitance and charging power: baseline circuit or quantitative model illustration
Model illustration at baseline inputs. Change the parameters in the next section to explore the live diagram.

Potential outside a conducting cylinder

E(x)=q'/(2\pi\epsilon x),\quad x\ge r

An ideal conductor has zero electric field inside its metal. Integrating the outside field uses the physical surface radius r; the internal magnetic-linkage correction does not apply to electric potential.

Phase-to-neutral capacitance

C'_n=\frac{2\pi\epsilon}{\ln(D_m/r)}\ \mathrm{F/m}

Balanced charges sum to zero. For equal spacing or a fully transposed arrangement, the mutual-distance terms reduce to GMD. The neutral is an electrical reference, not an added physical conductor.

From a rate to a route shunt

Y_{sh}=jB_{total}=j\omega C'_n\ell

Ctotal=C′ℓ and Btotal=ωCtotal. Unit conversions matter: nF/km multiplied by km gives nF, then divide by 1000 for μF. B is positive capacitive susceptance in Y=jB.

Current and three-phase reactive supply

|I_{ch,\phi}|=B_{total}\frac{V_{LL}}{\sqrt3},\quad Q_C=B_{total}V_{LL}^2

The phase charging current leads phase voltage by 90°. Under the uniform-voltage estimate, QC is positive capacitive supply; the absorbed complex reactive power is −QC. The line-voltage formula already includes all three phases.

Nominal π and local terminal voltage

I_{sh,S}=j\frac{B_{total}}2 V_S,\quad I_{sh,R}=j\frac{B_{total}}2 V_R

Each π end has jBtotal/2. Its current uses the local phase voltage. With equal terminal magnitudes, each end supplies half QC; otherwise compute each end separately. IR=0 means no receiving load, not zero sending charging current.

Baseline example: check each step

  1. Dm=(4×6×10)⅓=6.214465 m. ln(Dm/r)=6.09557759, using r=0.014 m.
  2. C′n=9.126699 nF/km; Ctotal=9.126699×120.7008/1000=1.1015999 μF.
  3. B′=3.4406845 μS/km; Btotal=0.41529337 mS. Each π-end shunt is 0.20764669 mS.
  4. Vphase=138/√3=79.67434 kV; |Ich|=33.08822 A. QC=0.41529337×138²/1000=7.908847 Mvar; absorbed Q=−7.908847 Mvar.
  5. Using magnetic GMR as r underestimates C′ by 3.944%. At 0.95 times voltage, QC becomes 0.95² times its original value, while C and B stay unchanged.
Original slide headings for this lecture32
  1. 1Transmission-Line Parameters III
  2. 2Lecture outline
  3. 3PART 1 · Charge, field, and voltage
  4. 4Charged conductor
  5. 5Electric-field quantities
  6. 6Field and potential difference
  7. 7PART 2 · Phase capacitance
  8. 8Balanced phase charge
  9. 9From individual charges to line voltage
  10. 10From line voltage to phase capacitance
  11. 11Transposed phase spacing
  12. 12Phase capacitance rate
  13. 13Geometry and capacitance
  14. 14PART 3 · Charging current and power
  15. 15Susceptance per unit length
  16. 16Route shunt totals
  17. 17Charging current
  18. 18Capacitive reactive power
  19. 19Nominal-π shunt split
  20. 20An unloaded energized line
  21. 21PART 4 · Exercises
  22. 22Exercise 1: given and find
  23. 23Exercise 1: solution
  24. 24Exercise 2: given
  25. 25Exercise 2: find
  26. 26Ex. 2(a): electric ratio
  27. 27Ex. 2(a): capacitance rate
  28. 28Ex. 2(b): susceptance rate
  29. 29Ex. 2(b): route totals
  30. 30Ex. 2(c): charging quantities
  31. 31Ex. 2(d): comparisons
  32. 32Summary
Cross-check the original slides

02 / EXPLORE

Change one input and explain the response

Reduce line voltage by 5% and predict QC before changing the slider. Then double length in Python: C, B, I and QC should double, while C′ stays fixed.

Advanced parameters / test readings

Preparing the model.

Geometric mean distance—
Phase-to-neutral capacitance rate—
Total route phase capacitance—
Total phase shunt susceptance—
Shunt susceptance at each π end—
Uniform-voltage phase charging current—
Three-phase capacitive supply—
Three-phase absorbed reactive power—

Charging reactive supply versus voltage

Capacitance versus physical radius

Current intermediate values and numerical checks

Balanced, equal-spacing or fully transposed overhead line in a uniform dielectric; earth and shield wires omitted. Charging uses uniform line voltage and does not solve sending/receiving voltage rise. The π diagram shows parameter placement; R and X are symbolic in this capacitance-only experiment.

03 / EDIT & COMPUTE

Edit code to reproduce the model independently

Reproduce the baseline, then modify the parameter scan. The source contains reusable independent model functions; edit the current function and inspect numerical checks.

case is a snapshot of the controls when you press Run. Call solve(case) and assign the final solution to result to plot it.

Download teaching models

The first run needs internet access to download Python. Computation stays in your browser; the solver uses only the standard library.

Ready to run.

Output appears here.
Inspect and edit the model source (advanced)

Edit this module's function and run again. case.module selects the module; solve(case) returns values, plots, and checks. The parameter experiment keeps the original JavaScript reference for comparison.

04 / CHECK & EXPLAIN

Companion experiment practice and feedback

Fixed practice inputs

L24 example: distances 4, 6 and 10 m; physical radius 14 mm; air ε=ε0=8.8541878×10⁻¹² F/m; f=60 Hz; length 75 mi=120.7008 km; VLL=138 kV. GMR=10.90 mm is supplied only for a deliberate comparison.

Practice uses fixed baseline inputs independently of the controls. Each field displays its tolerance.

±0.002 nF/km
±0.002 A
±0.002 Mvar

Which radius enters the capacitance formula?

Finally, explain in your own words

  1. What are the inputs, references, and main assumptions?
  2. Reduce line voltage by 5% and predict QC before changing the slider. Then double length in Python: C, B, I and QC should double, while C′ stays fixed.
  3. Did your code edit change physical parameters, the method, or representation bases? Which check helps identify that?

Passing numerical and understanding checks records this lecture’s companion practice as “practice checks passed.”

ECE 685 · L24

Course learning assistant

Ask about course material, request an explanation, or follow up.

Choose a context, then ask “What does this mean?”